Product Name: One-way plastic grille-way stretch plastic geogrid (use) one-way stretch geogrid is extruded from a polymer was pressed into sheets and then washed rules mesh, and then stretched longitudinally made. This process, linear polymer into the state and the formation of uniform distribution of node strength oblong mesh structure. This structure has a very high tensile strength and tensile modulus, especially my company more such products with ultra high international level of early (elongation at 2% -5%) tensile strength and tensile modulus . To the soil provides the ideal force commitment and proliferation of chains. The product tensile strength (> 150Mpa), adapt to a variety of soil, is widely used in reinforced reinforcement. (Usage) Uniaxial geogrid is a high strength geosynthetics. Widely used in dams, tunnels, docks, roads, railways, buildings and so on. Its main use is as follows: a reinforced embankment, can effectively spread the load and improve the stability and foundation bearing capacity and prolong life; 2 can withstand greater alternating load; 3 roadbed subgrade material to prevent the loss caused more. deformation and cracking; 4 so that the retaining wall after filling self-supporting capacity increase, decrease soil pressure retaining wall, to save costs, extend life and reduce maintenance costs; 5 with gunite concrete construction method Slope maintenance, not only can save 30% -50% of the investment, and can shorten the construction period more than doubled; 6 Join geogrid in the roadbed and road surface, you can reduce the deflection and reduce rutting, cracks delay time 3 -. 9 times, the structure thickness can be reduced by 36%; 7 for a variety of soils, drawn without remote, when labor-saving; 8 simple and quick construction, can greatly reduce construction costs. Product specifications and performance parameters of performance \ Specifications TGS-B-30-30 TGS-B-50-50 TGS-B-60-60 TGS-B-80-80 TGS-B - 100-100 EGA-B-80- 80-Z self-adhesive strength (KN / m) vertical 3050608010080 cross 3050608010080 Elongation% ≤ 3 ≤ 3 ≤ 3 ≤ 3 ≤ 3 ≤ 3 temperature resistance (℃) - modulus of elasticity of 100 to +280 676767676767 gel content ≤ 20% ≤ 20% ≤ 20% ≤ 20% ≤ 20% ≤ 20% premium asphalt surface treatment, adhesive polymer elastic material width (m) 1 - 6 1 - 6 1 - 6 1 - 6 1 - 6 1 - 6 network grid (mm) 25.4 × 25.4 25.4 × 25.4 25.4 × 25.4 25.4 × 25.4 25.4 × 25.4 25.4 × 25.4 corrosion Excellent Excellent Excellent Excellent Excellent Excellent unidirectional reinforced plastic grille an embankment, can effectively spread the load and improve the stability and foundation bearing capacity and prolong life; 2 can withstand greater alternating load; 3 roadbed subgrade material to prevent the loss caused by deformation and cracking; 4 so that the retaining wall after filling self-supporting capacity increase, decrease soil pressure retaining wall, to save costs, extend life and reduce maintenance costs; 5 with gunite concrete construction method Slope maintenance, not only can save 30% -50% of the investment, and can shorten the construction period more than doubled; 6 Join geogrid in the roadbed and road surface, you can reduce the deflection and reduce rutting, cracks delay time 3 -. 9 times, the structure thickness can be reduced by 36%; 7 for a variety of soils, drawn without remote, when labor-saving; 8 simple and quick construction, can greatly reduce construction costs. Waterproof board construction norms 1. Preparatory work before laying: 1.1 Ground handling: clean paved surfaces, requires matrix formation, soil solid, not uneven, cracks, etc., can not have sharp objects, stones, wire, sticks, etc., seepage within the turf, trees To remove the root, to spray herbicides for weed. 1.2 contact surface of the membrane, the laying of small particle size of sand or clay layer protective layer, the protective layer covering thickness of not less than 30 cm. 2. Laying method: 2.1 laying along a certain direction, but do not pull too tight, you should leave a certain amount of stretching to accommodate the deformation of the matrix. Waterproof Plate 2.2, to adjust each unit to facilitate the welding of the two units. 2.3 after laying waterproof board, use sand bags to suppress, to prevent wind affect the next edge welding 3. Waterproof board welding seams treatment is the key construction procedures, the general method of heat welding, PE film surface heat treatment, so that surface melting, and then through the pressure, so that fused together. 3.1 for paved waterproof board, then the edge joints request can not be pre-oil, water, dust, etc. 3.2 To adjust the welding seams two sides PE single film, so that a certain width lap, lap width is generally 6 to 8 cm and smooth, no crease. way stretch plastic geogrid is a kind of polymer (one-way plastic geogrid is a high-density polyethylene (HDPE) for raw materials, extrusion pressed into sheets and then washed rules mesh, then vertical stretching geogrid.) as the main raw material, adding some UV protection, anti-aging agent, through a one-way stretch so that the original distribution of scattered chain-shaped molecules arranged in a linear state reorientation high strength geotextile material . Much better than the traditional or existing reinforced material is ideal for civil engineering reinforcement, reinforced composite materials. Way plastic geogrid What characteristics: 1, polymer and formed into a linear state directional distribution, node strength oblong mesh structure. This structure has a very high tensile strength and rigidity to the soil provides ideal chains force commitment and proliferation. 2, one-way plastic geogrid advantage is sustainable in the long term load deformation (creep) the tendency of small, creep strength geogrid is much better than other materials, for improving the life of the project has an important role . 3, occlusal and mesh grille with interlocking effect between soil, constitutes an efficient stress transfer mechanism, so that the local load quickly and effectively spread to large areas of soil to go in order to achieve lower partial failure stress aims to improve the life of the project. Way plastic geogrid is a high strength geosynthetics. Widely used in dams, tunnels, docks, roads, railways, buildings and so on. Its main use is as follows: a reinforced embankment, can effectively spread the load and improve the stability and foundation bearing capacity and prolong life; 2 can withstand greater alternating load; 3 roadbed subgrade material to prevent the loss caused more. deformation and cracking; 4 so that the retaining wall after filling self-supporting capacity increase, decrease soil pressure retaining wall, to save costs, extend life and reduce maintenance costs; 5 with gunite concrete construction method Slope maintenance, not only can save 30% -50% of the investment, and can shorten the construction period more than doubled; 6 Join geogrid in the roadbed and road surface, you can reduce the deflection and reduce rutting, cracks delay time 3 -. 9 times, the structure thickness can be reduced by 36%; 7 for a variety of soils, drawn without remote, when labor-saving; 8 simple and quick construction, can greatly reduce construction costs.